Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Peoria?
Gate repair in Peoria typically costs $150 to $900, with most residential electric gate repairs landing between $280 and $650. A simple manual gate adjustment or hinge repair often runs $150 to $250, while control board replacement or loop detector work on an automatic driveway gate can reach $700 to $900. Full opener replacement usually falls between $550 and $1,400 depending on the operator and gate weight.
Those are estimates for the Peoria market in 2026. The written estimate we give you after we look at the gate sets the final price, and that estimate is free.
Key Takeaways
- Most Peoria gate repairs land between $150 and $900; electric gate work with control boards or loop detectors runs toward the top of that range.
- The biggest cost drivers are gate weight, operator brand, and whether the failure is mechanical or electronic.
- Our technicians have up to experience, and we service nine gate and access-control brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
- We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Gate Repair Cost Breakdown (2026)
Here’s how gate repair pricing in Peoria breaks down by job type. These are typical estimated ranges, not final quotes. Gate weight, brand availability, and site conditions move the number up or down, and the written estimate is what you pay.
| Repair Type | Typical Estimated Range | What It Covers |
|---|---|---|
| Manual gate hinge or latch repair | $150 – $250 | Worn hinges, sagging gates, latch alignment, roller replacement |
| Gate frame or post realignment | $200 – $450 | Straightening a leaning gate, tightening hardware, post footing work |
| Opener motor repair or replacement | $350 – $900 | Motor repair, gear replacement, full opener swap on residential gates |
| Control board replacement | $250 – $600 | Board diagnosis, same-brand or cross-brand board replacement |
| Safety sensor and photo-eye repair | $150 – $350 | Sensor realignment, wiring repair, replacement of failed safety loops |
| Loop detector and vehicle sensor repair | $250 – $600 | Loop diagnosis, detector replacement, saw-cut and re-loop on driveways |
| Intercom and keypad entry repair | $180 – $500 | Keypad, intercom, and access hardware repair or replacement |
| Battery backup and solar operator service | $200 – $550 | Battery replacement, solar panel and charging circuit repair |
| Full new gate installation (residential) | $2,500 – $7,500+ | New gate, operator, hardware, and access control |
What pushes a Peoria gate repair toward the top of these ranges? Gate weight is the big one. A heavy ornamental metal driveway gate puts more load on hinges, posts, and the opener than a lighter aluminum gate, so worn parts fail faster and replacement parts cost more. Brand matters too: a LiftMaster or DoorKing control board is usually straightforward to source, while some imported or older operators need cross-brand troubleshooting to get working again. Electronic failures – loop detectors, photo-eyes, intercoms – tend to cost more than mechanical ones because diagnosis takes longer. The condition of the gate frame and the driveway surface underneath the gate also affect the job. A gate dragging on cracked or heaved concrete needs the gate itself corrected, not just the opener adjusted.
What Affects Gate Repair Pricing in Peoria
Pricing isn’t random. These are the factors that move a gate repair estimate up or down in Peoria:
- Gate type and weight. A lightweight swing gate on a residential driveway is a different job from a full-perimeter commercial slide gate. Heavier panels mean heavier operators, beefier hardware, and more labor per repair.
- Operator brand and part availability. We work on nine brands, so we can often source same-brand replacement parts instead of quoting a full system swap. That alone can save hundreds on a repair.
- Mechanical versus electronic failure. A broken hinge is quick. A control board that’s dead but shows no obvious fault takes real diagnosis, and that time is part of the price.
- Access control and intercom. Gated communities and commercial properties often have keypads, intercoms, and vehicle loop detectors tied into the same system. Each connected component adds diagnosis and repair time.
- Property type. HOA and commercial gate repairs generally cost more than a single residential gate because of complexity, traffic flow, and the need to keep the gate operating during business hours.
- Peoria heat and sun exposure. Long summers here bake control boards, fade keypads, and wear out gate operators that sit in direct sun all day. Sun-exposed operators tend to fail on electronics before they fail mechanically, which shifts repair costs toward boards and sensors rather than hinges.
Gate Repair or Gate Replacement: Which Costs Less?
Repair almost always costs less than replacement when the gate frame and posts are sound. A $300 to $600 opener or control board repair is far cheaper than a $2,500 to $7,500 new gate installation. Replacement usually makes sense when the gate frame is bent or rusted through, the posts are failing, or the operator is obsolete and replacement parts no longer exist for that model.
We’re brand-agnostic on repair. If your existing gate and opener can be fixed, we fix them. We don’t push a brand switch when a same-brand part will do the job. If you do end up needing a new gate, we install as well as repair, so one call covers the whole job. You can read more about gate repair options for both manual and electric systems before you decide.
Manual Gate Repair vs. Electric Gate Repair Costs
Manual gate repair in Peoria generally runs $150 to $450 for hinge, latch, roller, and frame work. Electric gate repair runs higher, typically $250 to $900, because the opener, control board, safety sensors, and access hardware all sit on top of the mechanical gate.
Manual gates fail mechanically – sagging hinges, dragging latches, worn rollers, gate frames that shifted after monsoon wind or soil movement. Electric gates fail on top of that: dead motors, failed control boards, misaligned photo-eyes, burned-out loop detectors, intercoms that no longer connect. Diagnosing an electric gate means working through the whole chain: operator, board, sensors, and power. That’s why general handymen struggle with them and why a specialist diagnosis is worth the call.
How Much Does Electric Gate Repair Cost in Peoria?
Electric gate repair in Peoria usually costs $250 to $900 for residential systems and can run $400 to $1,400 for commercial or HOA gates with multiple access points. The range depends on whether the failure is in the motor, the control board, the safety sensors, or the access hardware.
We specialize in electric gate repair. That means we diagnose the motor, board, and sensors – not just the obvious. If your opener is a LiftMaster or a Mighty Mule, we know it. The nine brands we service cover the majority of residential and commercial gate operators installed across Peoria, from standard driveway swing gates to complex access systems with intercoms and loop detectors. If you want to understand the full scope of what each repair involves, our Gate Repair Peoria page walks through the service in detail.
What Does a New Gate Installation Cost in Peoria?
A new residential gate installation in Peoria typically costs $2,500 to $7,500 or more, including the gate, operator, hardware, and access control. Commercial and HOA installations run higher depending on gate size, traffic volume, and access requirements.
Installation pricing depends on gate material and width, operator brand, whether the gate is swing or slide, and what access hardware you need – keypad, intercom, loop detector, or all three. We handle new installation alongside repair, so you don’t get handed off to a second contractor if a repair turns into a replacement.
How to Save on Gate Repair
The single biggest way to save on a Peoria gate repair is to fix it early. A misaligned photo-eye costs $150 to $350 to correct. Ignored, it can wear out the control board and turn into a $600 job. These are practical steps that keep repair costs on the low end:
- Get the estimate in writing before work starts. Free on-site estimates tell you exactly what’s wrong and what the repair costs. Ours are free and set the final price.
- Repair the part, don’t replace the system. If a same-brand replacement part gets your existing operator working, take it. We don’t push full replacements when a repair will do.
- Fix small mechanical issues before they become electronic ones. A dragging gate overloads the opener motor. Straightening the gate early is cheaper than replacing a burned-out motor later.
- Keep the operator shaded where possible. Sun exposure wears out control boards and keypads faster here. A simple shade structure over the operator housing stretches its life.
- Stay current on mechanical checks. Hinges, rollers, and latches wear predictably. Catching a worn hinge at $150 to $250 beats repairing a bent gate frame at $200 to $450.
If your gate is acting up, call (855) 574-0402. We answer 24/7, and the estimate is free.
FAQs – Gate Repair Cost in Peoria
How much does gate repair cost in Peoria?
Gate repair in Peoria typically costs $150 to $900, with most repairs landing between $280 and $650. Manual gate repairs run lower ($150 to $450); electric gate work with control boards, sensors, or loop detectors runs higher ($250 to $900). Call (855) 574-0402 for an exact quote – estimates are free.
Is it cheaper to repair or replace a gate?
Repair is almost always cheaper. A $300 to $600 repair beats a $2,500 to $7,500 new gate installation. Replacement makes sense when the gate frame or posts are structurally failing, or the operator is obsolete with no available parts. Call (855) 574-0402 and we’ll tell you which applies to your gate.
How much does electric gate repair cost in Peoria?
Electric gate repair in Peoria usually costs $250 to $900 for residential systems and $400 to $1,400 for commercial or HOA gates. The range depends on whether the failure is in the motor, control board, safety sensors, or access hardware. Call (855) 574-0402 for an exact quote – estimates are free.
Can you come today?
Same-day service is often available. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. Call (855) 574-0402 to check availability and get a free estimate.
What brands do you repair?
We service nine gate and access-control brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That breadth means we can often source same-brand parts instead of quoting a full system replacement. Call (855) 574-0402 to confirm we cover your gate’s brand.
What happens when I call outside dispatch hours?
We answer 24/7. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (855) 574-0402 – the estimate is free.
Contact Us for a Free Gate Repair Estimate in Peoria
If your gate is sticking, dragging, or the opener is dead, call (855) 574-0402. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Our technicians have up to experience, and we work on manual gates, electric gates, and new installations. We specialize exclusively in gates – it’s all we do. Nine brands, one specialist, no runaround.
Pricing reflects the Peoria market as of 2026. Gate Repair Peoria offers free estimates – call (855) 574-0402.
What Our Customers Say
"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, swapped it, and we were moving cars again in under an hour."
- Marcy Ziegler"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Maya Shah"Repair is holding. He was quite a bit later than the window I was given, and nobody called me about it, I had to call them. The work itself was done well once he got here."
- Eric Mercer